Omnisphere 3 Hardware Guide

Search

The topic you requested could not be found.
Related topics are listed below.

Setting Up the Komplete Kontrol S25 mk1

Controllers » Native Instruments » Setting Up the Komplete Kontrol S25 mk1

When using the NI Komplete Kontrol S25 mk1 to control Omnisphere, the knobs on the Komplete Kontrol S25 mk1 are assigned to the following Omnisphere parameters: Knob 1 (CC#14) – Global Controls Cutoff Knob 2 (CC#15) – Global Controls…

Setting Up the Komplete Kontrol S49 mk3

Controllers » Native Instruments » Setting Up the Komplete Kontrol S49 mk3

When using the NI Komplete Kontrol S49 mk3 to control Omnisphere, the knobs on the Komplete Kontrol S49 mk3 are assigned to the following Omnisphere parameters: Knob 1 (CC#14) – Global Controls Cutoff Knob 2 (CC#15) – Global Controls Resonance Knob…

Setting Up the Komplete Kontrol S61 mk3

Controllers » Native Instruments » Setting Up the Komplete Kontrol S61 mk3

When using the NI Komplete Kontrol S61 mk3 to control Omnisphere, the knobs on the Komplete Kontrol S61 mk3 are assigned to the following Omnisphere parameters: Knob 1 (CC#14) – Global Controls Cutoff Knob 2 (CC#15) – Global Controls Resonance Knob…

Setting Up the Komplete Kontrol S88 mk3

Controllers » Native Instruments » Setting Up the Komplete Kontrol S88 mk3

When using the NI Komplete Kontrol S88 mk3 to control Omnisphere, the knobs on the Komplete Kontrol S88 mk3 are assigned to the following Omnisphere parameters: Knob 1 (CC#14) – Global Controls Cutoff Knob 2 (CC#15) – Global Controls…

Setting Up the Komplete Kontrol A49

Controllers » Native Instruments » Setting Up the Komplete Kontrol A49

When using the NI Komplete Kontrol A49 to control Omnisphere, the knobs on the Komplete Kontrol A49 are assigned to the following Omnisphere parameters: Knob 1 (CC#14) – Global Controls Cutoff Knob 2 (CC#15) – Global Controls Resonance Knob 3…

Setting Up the Komplete Kontrol A25

Controllers » Native Instruments » Setting Up the Komplete Kontrol A25

When using the NI Komplete Kontrol A25 to control Omnisphere, the knobs on the Komplete Kontrol A25 are assigned to the following Omnisphere parameters: Knob 1 (CC#14) – Global Controls Cutoff Knob 2 (CC#15) – Global Controls Resonance Knob 3…

Setting Up the Komplete Kontrol M32

Controllers » Native Instruments » Setting Up the Komplete Kontrol M32

When using the NI Komplete Kontrol M32 to control Omnisphere, the knobs on the Komplete Kontrol M32 are assigned to the following Omnisphere parameters: Knob 1 (CC#14) – Global Controls Cutoff Knob 2 (CC#15) – Global Controls Resonance Knob 3…

Setting Up the Komplete Kontrol A61

Controllers » Native Instruments » Setting Up the Komplete Kontrol A61

When using the NI Komplete Kontrol A61 to control Omnisphere, the knobs on the Komplete Kontrol A61 are assigned to the following Omnisphere parameters: Knob 1 (CC#14) – Global Controls Cutoff Knob 2 (CC#15) – Global Controls Resonance Knob 3…

Setting Up the Komplete Kontrol S88 mk2

Controllers » Native Instruments » Setting Up the Komplete Kontrol S88 mk2

When using the NI Komplete Kontrol S88 mk2 to control Omnisphere, the knobs on the Komplete Kontrol S88 mk2 are assigned to the following Omnisphere parameters: Knob 1 (CC#14) – Global Controls Cutoff Knob 2 (CC#15) – Global Controls…

Setting Up the Komplete Kontrol S61 mk1

Controllers » Native Instruments » Setting Up the Komplete Kontrol S61 mk1

When using the NI Komplete Kontrol S61 mk1 to control Omnisphere, the knobs on the Komplete Kontrol S61 mk1 are assigned to the following Omnisphere parameters: Knob 1 (CC#14) – Global Controls Cutoff Knob 2 (CC#15) – Global Controls…

Setting Up the Komplete Kontrol S61 mk2

Controllers » Native Instruments » Setting Up the Komplete Kontrol S61 mk2

When using the NI Komplete Kontrol S61 mk2 to control Omnisphere, the knobs on the Komplete Kontrol S61 mk2 are assigned to the following Omnisphere parameters: Knob 1 (CC#14) – Global Controls Cutoff Knob 2 (CC#15) – Global Controls…

Setting Up the Komplete Kontrol S88 mk1

Controllers » Native Instruments » Setting Up the Komplete Kontrol S88 mk1

When using the NI Komplete Kontrol S88 mk1 to control Omnisphere, the knobs on the Komplete Kontrol S88 mk1 are assigned to the following Omnisphere parameters: Knob 1 (CC#14) – Global Controls Cutoff Knob 2 (CC#15) – Global Controls…

Setting Up the Komplete Kontrol S49 mk2

Controllers » Native Instruments » Setting Up the Komplete Kontrol S49 mk2

When using the NI Komplete Kontrol S49 mk2 to control Omnisphere, the knobs on the Komplete Kontrol S49 mk2 are assigned to the following Omnisphere parameters: Knob 1 (CC#14) – Global Controls Cutoff Knob 2 (CC#15) – Global Controls Resonance Knob…

Setting Up the Komplete Kontrol S49 mk1

Controllers » Native Instruments » Setting Up the Komplete Kontrol S49 mk1

When using the NI Komplete Kontrol S49 mk1 to control Omnisphere, the knobs on the Komplete Kontrol S49 mk1 are assigned to the following Omnisphere parameters: Knob 1 (CC#14) – Global Controls Cutoff Knob 2 (CC#15) – Global Controls…

Setting Up the Maschine mk3

Controllers » Native Instruments » Setting Up the Maschine mk3

When using the Native Instruments Maschine mk3 to control Omnisphere, the following knobs on the Maschine mk3 are assigned to the following Omnisphere parameters: Knob 1 (CC#70) – Global Controls Cutoff Knob 2 (CC#71) – Global Controls…

Setting Up the Minilab mk3

Controllers » Arturia » Setting Up the Minilab mk3

When using the Arturia MiniLab mk3 to control Omnisphere, the knobs and faders on the MiniLab mk3 are assigned to the following Omnisphere parameters: Knob 1 (CC#74) – Global Controls Cutoff Knob 2 (CC#71) – Global Controls Resonance Knob 3 (CC#76)…

Setting Up the Launchkey 88 mk3

Controllers » Novation » Setting Up the Launchkey 88 mk3

When using the Novation Launchkey 88 mk3 to control Omnisphere, the knobs, faders, and drum pads on the Launchkey 88 mk3 are assigned to the following Omnisphere parameters: Knob 1 (CC#21) – Global Controls Cutoff Knob 2 (CC#22) – Global Controls…

Setting Up the Launchkey Mini mk3

Controllers » Novation » Setting Up the Launchkey Mini mk3

When using the Novation Launchkey Mini mk3 to control Omnisphere, the knobs on the Launchkey Mini mk3 are assigned to the following Omnisphere parameters: Knob 1 (CC#21) – Global Controls Cutoff Knob 2 (CC#22) – Global Controls Resonance Knob 3…

Setting Up the Launchkey 61 mk3

Controllers » Novation » Setting Up the Launchkey 61 mk3

When using the Novation Launchkey 61 mk3 to control Omnisphere, the knobs, faders, and drum pads on the Launchkey 61 mk3 are assigned to the following Omnisphere parameters: Knob 1 (CC#21) – Global Controls Cutoff Knob 2 (CC#22) – Global Controls…

Setting Up the Launchkey 49 mk3

Controllers » Novation » Setting Up the Launchkey 49 mk3

When using the Novation Launchkey 49 mk3 to control Omnisphere, the knobs, faders, and drum pads on the Launchkey 49 mk3 are assigned to the following Omnisphere parameters: Knob 1 (CC21) – Global Controls Cutoff Knob 2 (CC22) – Global Controls…

Setting Up the Launchkey 37 mk3

Controllers » Novation » Setting Up the Launchkey 37 mk3

When using the Novation Launchkey 37 mk3 to control Omnisphere, the knobs and drum pads on the Launchkey 37 mk3 are assigned to the following Omnisphere parameters: Knob 1 (CC#21) – Global Controls Cutoff Knob 2 (CC#22) – Global Controls…

Setting Up the Launchkey 25 mk3

Controllers » Novation » Setting Up the Launchkey 25 mk3

When using the Novation Launchkey 25 mk3 to control Omnisphere, the knobs and drum pads on the Launchkey 25 mk3 are assigned to the following Omnisphere parameters: Knob 1 (CC#21) – Global Controls Cutoff Knob 2 (CC#22) – Global Controls…

Setting Up the Impact LX88 mk3

Controllers » Nektar » Setting Up the Impact LX88 mk3

When using the Nektar Impact LX88 mk3 to control Omnisphere, the knobs and fader on the Impact LX88 mk3 are assigned to the following Omnisphere parameters: Bottom row of knobs: Knob 1 (CC#89) – Global Controls Cutoff Knob 2 (CC#90) – Global…

Setting Up the Impact LX61 mk3

Controllers » Nektar » Setting Up the Impact LX61 mk3

When using the Nektar Impact LX61 mk3 to control Omnisphere, the knobs and fader on the Impact LX61 mk3 are assigned to the following Omnisphere parameters: Bottom row of knobs: Knob 1 (CC#89) – Global Controls Cutoff Knob 2 (CC#90) – Global…

Setting Up the Impact LX49 mk3

Controllers » Nektar » Setting Up the Impact LX49 mk3

When using the Nektar Impact LX49 mk3 to control Omnisphere, the knobs, faders, and buttons on the Impact LX49 mk3 are assigned to the following Omnisphere parameters: Bottom row of knobs: Knob 1 (CC#89) – Global Controls Cutoff Knob 2 (CC#90) –…

Setting Up the Impact LX25 mk3

Controllers » Nektar » Setting Up the Impact LX25 mk3

When using the Nektar Impact LX25 mk3 to control Omnisphere, the knobs on the Impact LX25 mk3 are assigned to the following Omnisphere parameters: Top row of knobs: Knob 5 (CC#116) – Global Controls Glide Knob 6 (CC#117) – Global Controls…

Setting up the MPK Mini mk3

Controllers » Akai » Setting up the MPK Mini mk3

When using the Akai MPK Mini mk3 to control Omnisphere, the knobs and drum pads on the MPK Mini mk3 are assigned to the following Omnisphere parameters: Knob 1 (CC#70) – Global Controls Cutoff Knob 2 (CC#71) – Global Controls Resonance Knob 3…

Setting Up the KeyLab 49 mk3

Controllers » Arturia » Setting Up the KeyLab 49 mk3

When using the Arturia KeyLab 49 mk3 to control Omnisphere, the knobs, sliders, and buttons on the KeyLab 49 mk3 are assigned to the following Omnisphere parameters: Knob 1 (CC#74) – Global Controls Cutoff Knob 2 (CC#71) – Global Controls…

Setting Up the KeyLab 61 mk3

Controllers » Arturia » Setting Up the KeyLab 61 mk3

When using the Arturia KeyLab 61 mk3 to control Omnisphere, the knobs, sliders, and buttons on the KeyLab 61 mk3 are assigned to the following Omnisphere parameters: Knob 1 (CC#74) – Cutoff Knob 2 (CC#71) – Res Knob 3 (CC#76) – Flt Env Knob 4…

Setting Up the KeyLab 88 mk3

Controllers » Arturia » Setting Up the KeyLab 88 mk3

When using the Arturia KeyLab 88 mk3 to control Omnisphere, the knobs, faders, and buttons on the KeyLab 88 mk3 are assigned to the following Omnisphere parameters: Knob 1 (CC#74) – Global Controls Cutoff Knob 2 (CC#71) – Global Controls…

Setting Up the Launch Control XL mk3

Controllers » Novation » Setting Up the Launch Control XL mk3

When using the Novation Launch Control XL mk3 to control Omnisphere, the knobs, faders, and buttons on the Launch Control XL mk3 are assigned to the following Omnisphere parameters: Top Row of Knobs: Knob 1 (CC#13) – Global Controls Cutoff Knob 2 (CC#14)…

Setting up the MPK Mini Play mk3

Controllers » Akai » Setting up the MPK Mini Play mk3

When using the Akai MPK Mini Play mk3 to control Omnisphere, the knobs on the MPK Mini Play mk3 are assigned to the following Omnisphere parameters: Bank A: Knob 1 (CC#70) – Global Controls Cutoff Knob 2 (CC#71) – Global Controls Resonace Knob 3…

Setting Up the KeyLab Essential 61 mk3

Controllers » Arturia » Setting Up the KeyLab Essential 61 mk3

When using the Arturia KeyLab Essential 61 mk3 to control Omnisphere, the knobs, sliders, and buttons on the KeyLab Essential 61 mk3 are assigned to the following Omnisphere parameters: Knob 1 (CC#74) – Global Controls Cutoff Knob 2 (CC#71) – Global…

Setting Up the KeyLab Essential 49 mk3

Controllers » Arturia » Setting Up the KeyLab Essential 49 mk3

When using the Arturia KeyLab Essential 49 mk3 to control Omnisphere, the knobs, sliders, and buttons on the KeyLab Essential 49 mk3 are assigned to the following Omnisphere parameters: Knob 1 (CC#74) – Global Controls Cutoff Knob 2 (CC#71) – Global…

Setting Up the KeyLab Essential 88 mk3

Controllers » Arturia » Setting Up the KeyLab Essential 88 mk3

When using the Arturia KeyLab Essential 88 mk3 to control Omnisphere, the knobs, sliders, and buttons on the KeyLab Essential 88 mk3 are assigned to the following Omnisphere parameters: Knob 1 (CC#74) – Global Controls Cutoff Knob 2 (CC#71) – Global…

Setting Up The Laboratory

Controllers » Arturia » Setting Up The Laboratory

When using the Arturia Laboratory to control Omnisphere, the knobs and sliders on the Laboratory are assigned to the following Omnisphere parameters: Knob 01 (CC#74) – Global Controls Cutoff Knob 02 (CC#71) – Global Controls Resonance Knob 03…

Setting Up The Player

Controllers » Arturia » Setting Up The Player

When using the Arturia Player to control Omnisphere, the knobs and sliders on the Player are assigned to the following Omnisphere parameters: First Bank: Knob 1 (CC#74) – Global Controls Cutoff Knob 2 (CC#71) – Global Controls Resonance Knob 3…

Setting up the Minitaur

Synthesizers » Moog » Moog Minitaur » Setting up the Minitaur

Setup To control Omnisphere using the Minitaur you’ll need to do the following: Connect the Minitaur’s to your computer via USB. Set the Mintaur’s Decay/Release Mode to “Mode 2.” Activate the Moog Minitaur Hardware Profile in…

Setting up the Prologue

Synthesizers » Korg » Korg Prologue » Setting up the Prologue

Setup To control Omnisphere using the Korg Prologue, you’ll need to do the following: Using a USB cable, connect the Prologue to your computer. Verify that your Prologue is transmitting MIDI through USB. Verify that your Prologue is using the latest…

Setting up the Sirin

Synthesizers » Moog » Moog Sirin » Setting up the Sirin

Setup To control Omnisphere using the Sirin you’ll need to do the following: Connect the Sirin’s USB connector to your computer. Set the Sirin’s Decay/Release Mode to “Mode 2.” Activate the Moog Sirin Hardware Profile in Omnisphere 3…

Setting up the REV2

Synthesizers » Sequential » Sequential REV2 » Setting up the REV2

Setup To control Omnisphere using the REV2, you’ll need to do the following: Using a USB cable, connect the REV2 to your computer. Verify that your REV2 is transmitting MIDI through USB. Set up the front panel controls to NRPN mode. Enable the REV2 as a…

Setting up the Mopho

Synthesizers » Sequential » Sequential Mopho » Setting up the Mopho

Setup To control Omnisphere using Mopho, you’ll need to do the following: Connect the Mopho to your MIDI interface. Set up the Mopho’s front panel controls to send NRPNs. Make certain your MIDI interface is configured as the input in the host software…

Setting up the Matrixbrute

Synthesizers » Arturia » Arturia Matrixbrute » Setting up the Matrixbrute

Setup To control Omnisphere using the Matrixbrute, follow these steps: Connect the Matrixbrute to your computer via USB. Enable the Matrixbrute as a MIDI input device in the host software you’re using (DAW, Standalone, etc.). Activate the Matrixbrute…

Setting up the MiniFreak

Synthesizers » Arturia » Arturia MiniFreak » Setting up the MiniFreak

Setup To control Omnisphere using the Minifreak, follow these steps: Connect the Minifreak to your computer via USB. Set up the front panel controls to send MIDI CCs. Enable the Minifreak as a MIDI input device in the host software you’re using (DAW,…

Setting up the Monologue

Synthesizers » Korg » Korg Monologue » Setting up the Monologue

Setup To control Omnisphere using the Korg Monologue, you’ll need to do the following: Using a USB cable, connect the Monologue to your computer. Verify that your Monologue is transmitting MIDI through USB. Enable the Monologue as a MIDI input device to…

Setting up the Minilogue

Synthesizers » Korg » Korg Minilogue » Setting up the Minilogue

Setup To control Omnisphere using the Korg Minilogue, you’ll need to do the following: Using a USB cable, connect the Minilogue to your computer. Verify that your Minilogue is transmitting MIDI through USB. Enable the Minilogue as a MIDI input device to…

Setting up the Mininova

Synthesizers » Novation » Novation Mininova » Setting up the Mininova

Setup To control Omnisphere using the Mininova, you’ll need to do the following: Download and install the latest Novation driver for the Mininova. Connect the Mininova’s USB port to your computer via USB. Activate the Novation Mininova Hardware Profile…

Setting Up the MODX

Controllers » Yamaha » Setting Up the MODX

The Yamaha MODX is an extremely powerful workstation that can be used for a wide variety of musical applications, from composition and recording to live performance, including the ability to control external devices. When using the MODX to control Omnisphere, the…

Setting Up the MPD232

Controllers » Akai » Setting Up the MPD232

When using the Akai MPD232 to control Omnisphere, the knobs and sliders on the MPD232 are assigned to the following Omnisphere parameters: Knob 1 (CC#03) – Global Controls Cutoff Knob 2 (CC#09) – Global Controls Resonance Knob 3 (CC#14) –…

Setting Up the nanoKONTROL

Controllers » Korg » Setting Up the nanoKONTROL

When using the Korg nanoKONTROL to control Omnisphere, the following knobs and sliders on the nanoKONTROL are assigned to the following Omnisphere parameters: Knob 1 (CC#14) – Global Controls Cutoff Knob 2 (CC#15) – Global Controls Resonance Knob 3…

Setting Up the nanoKONTROL2

Controllers » Korg » Setting Up the nanoKONTROL2

When using the Korg nanoKONTROL22 to control Omnisphere, the following knobs on the nanoKONTROL22 are assigned to the following Omnisphere parameters: Knob 1 (CC#16) – Global Controls Amp Envelope Attack Knob 2 (CC#17) – Global Controls Amp Envelope…

Setting Up the UC4

Controllers » FaderFox » Setting Up the UC4

When using the FaderFox UC4 to control Omnisphere, the knobs and faders on the UC4 are assigned to the following Omnisphere parameters: Knob 1 (CC#08) – Global Controls Cutoff Knob 2 (CC#09) – Global Controls Resonance Knob 3 (CC#10) – Global…

Setting Up the MODX+

Controllers » Yamaha » Setting Up the MODX+

The Yamaha MODX+ is an extremely powerful workstation that can be used for a wide variety of musical applications, from composition and recording to live performance, including the ability to control external devices. When using the MODX+ to control Omnisphere, the…

Setting Up The Factory

Controllers » Arturia » Setting Up The Factory

When using the Arturia Factory to control Omnisphere, the knobs and sliders on the Factory are assigned to the following Omnisphere parameters: Knob 01 (cc74) – Global Controls Cutoff Knob 02 (cc71) – Global Controls Resoance Knob 03 (cc76) –…

Setting Up the MOXF

Controllers » Yamaha » Setting Up the MOXF

The Yamaha MOXF series are extremely powerful workstations that can be used for a wide variety of musical applications, from composition and recording to live performance, including the ability to control external devices. When using any of the MOXF workstations to…

Setting Up the MX

Controllers » Yamaha » Setting Up the MX

The Yamaha MX series (the MX49 and MX61) are extremely powerful workstations that can be used for a wide variety of musical applications, from composition and recording to live performance, including the ability to control external devices. When using any of the MX…

Setting Up the Montage

Controllers » Yamaha » Setting Up the Montage

The Yamaha Montage is an extremely powerful workstation that can be used for a wide variety of musical applications, from composition and recording to live performance, including the ability to control external devices. When using the Montage to control Omnisphere,…

Setting up the DeepMind

Synthesizers » Behringer » Behringer DeepMind » Setting up the DeepMind

Setup To control Omnisphere using the Deepmind 6 or Deepmind 12, you’ll need to do the following: Connect the Deepmind to your computer via USB. Set up the front panel controls to send NRPNs. Enable the Deepmind as a MIDI input device in the host software…

Setting up the Sledge

Synthesizers » Studiologic Sledge » Setting up the Sledge

Setup To control Omnisphere using the Studiologic Sledge you’ll need to do the following: Using a USB cable, connect the Sledge to your computer. Verify that your Sledge is transmitting MIDI through USB. Set up the front panel controls to send CCs. Enable…

Setting up the Cobalt5S

Synthesizers » Modal » Modal Cobalt5S » Setting up the Cobalt5S

Setup To control Omnisphere using the Cobalt5S, you’ll need to do the following: Using a USB cable, connect the Cobalt5S to your computer. Enable “Cobalt5S” as a MIDI input device to Omnisphere in the host software you’re using (DAW, Standalone,…

Setting up the Cobalt8

Synthesizers » Modal » Modal Cobalt8 » Setting up the Cobalt8

Setup To control Omnisphere using the Cobalt8, you’ll need to do the following: Using a USB cable, connect the Cobalt8 h to your computer. Enable “Cobalt8” as a MIDI input device to Omnisphere in the host software you’re using (DAW, Standalone,…

Setting up the Radias

Synthesizers » Korg » Korg Radias » Setting up the Radias

Setup To control Omnisphere using the Korg Radias, you’ll need to do the following: Connect the Radias to your MIDI interface. Set up the front panel controls to send MIDI. Activate the Korg Radias Hardware Profile in Omnisphere 3 or later. MIDI OUTPUT…

Setting up the Muse

Synthesizers » Moog » Moog Muse » Setting up the Muse

Setup To control Omnisphere using the Moog Muse you’ll need to do the following: Using a USB cable, connect the Muse to your computer. Download and install the latest Moog Muse firmware from the Moog website here. Enable the Muse as a MIDI input device to…

Setting up the Argon8

Synthesizers » Modal » Modal Argon8 » Setting up the Argon8

Setup To control Omnisphere using the Argon8, you’ll need to do the following: Using a USB cable, connect the Argon8 h to your computer. Enable “Argon8” as a MIDI input device to Omnisphere in the host software you’re using (DAW, Standalone,…

Setting up the Messenger

Synthesizers » Moog » Moog Messenger » Setting up the Messenger

Setup To control Omnisphere using the Moog Messenger you’ll need to do the following: Using a USB cable, connect the Messenger to your computer. Download and install the latest Moog Messenger firmware from the Moog website here. Enable the Messenger as a…

Setting up the Voyager

Synthesizers » Moog » Moog Voyager » Setting up the Voyager

Setup To control Omnisphere using the Voyager, you’ll need to do the following: Using a MIDI interface, connect the Voyager to your computer. Enable the Voyager as a MIDI input device to Omnisphere in the host software you’re using (DAW, Standalone,…

Setting up the Peak

Synthesizers » Novation » Novation Peak » Setting up the Peak

Setup To control Omnisphere using the Novation Peak, you’ll need to do the following: Using a USB cable, connect the Novation Peak to your computer. If you’re using a Windows-based system, download the Novation USB Driver. Set up the front panel…

Setting up the Summit

Synthesizers » Novation » Novation Summit » Setting up the Summit

Setup To control Omnisphere using the Novation Summit, you’ll need to do the following: Using a USB cable, connect the Novation Summit to your computer. If you’re using a Windows-based system, download the Novation USB Driver. Set up the front panel…

Setting up the Drop

Controllers » Neuzeit Instruments » Setting up the Drop

When using the Neuzeit Instruments Drop to control Omnisphere, the knobs and faders on the Drop are assigned to the following Omnisphere parameters: Top row of knobs: Knob 1 (CC#01) – Mod Wheel Knob 2 (CC#02) – Global Controls Cutoff Knob 3…

Setting Up the MAX25

Controllers » Akai » Setting Up the MAX25

When using the Akai MAX25 to control Omnisphere, the Touch Faders on the MAX25 are assigned to the following Omnisphere parameters: Bank 1-4: Touch Fader 1 (CC#20) – Global Controls Cutoff Touch Fader 2 (CC#21) – Global Controls Ambience…

Setting Up the MAX49

Controllers » Akai » Setting Up the MAX49

When using the Akai MAX49 to control Omnisphere, the Touch Faders on the MAX49 are assigned to the following Omnisphere parameters: Bank 1-4: Touch Fader 1 (CC#12) – Global Controls Cutoff Touch Fader 2 (CC#13) – Global Controls Resonance Touch…

Setting Up the MIDImix

Controllers » Akai » Setting Up the MIDImix

When using the Akai MIDImix to control Omnisphere, the following knobs and faders on the MIDImix are assigned to the following Omnisphere parameters: Top row of knobs: Knob 1 (CC#16) – Global Controls Cutoff Knob 2 (CC#20) – Global Controls…

Setting Up The MPD226

Controllers » Akai » Setting Up The MPD226

When using the Akai MPD226 to control Omnisphere, the knobs on the MPD226 are assigned to the following Omnisphere parameters: Knob 1 (CC#03) – Global Controls Cutoff Knob 2 (CC#09) – Global Controls Resonance Knob 3 (CC#14) – Global Controls…

Setting Up the MPD218

Controllers » Akai » Setting Up the MPD218

When using the Akai MPD218 to control Omnisphere, the knobs on the MPD218 are assigned to the following Omnisphere parameters: Knob 1 (CC#03) – Global Controls Cutoff Knob 2 (CC#09) – Global Controls Env Knob 3 (CC#12) – Global Controls…

Setting Up the MPK261

Controllers » Akai » Setting Up the MPK261

When using the Akai MPK261 to control Omnisphere, the knobs and buttons on the MPK261 are assigned to the following Omnisphere parameters: Knob 1 (CC#83) – Global Controls Cutoff Knob 2 (CC#85) – Global Controls Resonance Knob 3 (CC#86) –…

Setting up the MPK249

Controllers » Akai » Setting up the MPK249

When using the Akai MPK249 to control Omnisphere, the knobs and buttons on the MPK249 are assigned to the following Omnisphere parameters: Knob 1 (CC#83) – Global Controls Cutoff Knob 2 (CC#85) – Global Controls Resonance Knob 3 (CC#86) –…

Setting Up the Exquis

Controllers » Intuitive Instruments » Setting Up the Exquis

When using the Intuitive Instruments Exquis to control Omnisphere, the knobs on the Exquis are assigned to the following Omnisphere parameters: Knob 1 (CC#14) – Global Controls Cutoff Knob 2 (CC#15) – Global Controls Ambience Amount Knob 3 (CC#16)…

Setting Up the QueNeo

Controllers » Keith McMillen » Setting Up the QueNeo

When using the Keith McMillen QueNeo to control Omnisphere, the sliders and drum pads on the QueNeo are assigned to the following Omnisphere parameters: Top 4 Sliders: Slider 1 (CC#00) – Global Controls Cutoff Slider 2 (CC#01) – Mod Wheel Slider 3…

Setting Up the VI61

Controllers » Alesis » Setting Up the VI61

When using the Alesis VI61 to control Omnisphere, the Knobs on the VI61 are assigned to the following Omnisphere parameters: Knob 01 (CC#20) – Global Controls Cutoff Knob 02 (CC#21) – Global Controls Resoance Knob 03 (CC#22) – Global…

Setting Up the VI49

Controllers » Alesis » Setting Up the VI49

When using the Alesis VI49 to control Omnisphere, the Knobs on the VI49 are assigned to the following Omnisphere parameters: Knob 01 (CC#20) – Global Controls Cutoff Knob 02 (CC#21) – Global Controls Resonance Knob 03 (CC#22) – Global…

Setting Up the VI25

Controllers » Alesis » Setting Up the VI25

When using the Alesis VI25 to control Omnisphere, the Knobs on the VI25 are assigned to the following Omnisphere parameters: Knob 1 (C#C20) – Global Controls Cutoff Knob 2 (CC#21) – Global Controls Resonance Knob 3 (CC#22) – Global Controls…

Setting Up the KARMA

Controllers » Korg » Setting Up the KARMA

When using the Korg KARMA to control Omnisphere, the following knobs on the KARMA are assigned to the following Omnisphere parameters: KARMA Realtime Controls: Knob 1 (CC#22) – Global Controls Cutoff Knob 2 CC#23) – Global Controls Resonance Knob…

Setting Up the KROME

Controllers » Korg » Setting Up the KROME

When using the Korg KROME to control Omnisphere, the following knobs on the KROME are assigned to the following Omnisphere parameters: TONE Mode: Knob 1 (CC#74) – Global Controls Cutoff Knob 2 (CC#71) – Global Controls Resonance Knob 3 (CC#79)…

Setting Up the BeatStep

Controllers » Arturia » Setting Up the BeatStep

When using the Arturia BeatStep to control Omnisphere, the knobs on the BeatStep are assigned to the following Omnisphere parameters: Knob 01 (CC#10) – Global Controls Cutoff Knob 02 (CC#74) – Global Controls Resonance Knob 03 (CC#71) –…

Setting Up the Ozonic

Controllers » M-Audio » Setting Up the Ozonic

When using the M-Audio Ozonic to control Omnisphere, the knobs and sliders on the Ozonic are assigned to the following Omnisphere parameters: Knob 1 (CC#10) – Global Controls Cutoff Knob 2 (CC#02) – Global Controls Resonance Knob 3 (CC#92) –…

Setting Up the M3

Controllers » Korg » Setting Up the M3

When using the Korg M3 to control Omnisphere, the following sliders on the M3 are assigned to the following Omnisphere parameters: Slider 1 (CC#08) – Global Controls Cutoff Slider 2 (CC#71) – Global Controls Resonance Slider 3 CC#74) –…

Setting Up the M50

Controllers » Korg » Setting Up the M50

When using the Korg M50 to control Omnisphere, the following knobs on the M50 are assigned to the following Omnisphere parameters: External bank 1: Knob 1 (CC#08) – Global Controls Cutoff Knob 2 (CC#71) – Global Controls Resonance Knob 3 (CC#74)…

Setting Up the O2

Controllers » M-Audio » Setting Up the O2

When using the M-Audio O2 to control Omnisphere, the knobs on the O2 are assigned to the following Omnisphere parameters: Knob 1 (CC#73) – Global Controls Cutoff Knob 2 (CC#72) – Global Controls Resonance Knob 3 (CC#74) – Global Controls…

Setting Up the microSTATION

Controllers » Korg » Setting Up the microSTATION

When using the Korg microSTATION to control Omnisphere, the following knobs on the microSTATION are assigned to the following Omnisphere parameters: Knob 1 (CC#08) – Global Controls Cutoff Knob 2 (CC#71) – Global Controls Ambience Amount Knob 3…

Setting Up the NAUTILUS

Controllers » Korg » Setting Up the NAUTILUS

When using the Korg NAUTILUS to control Omnisphere, the following knobs on the NAUTILUS are assigned to the following Omnisphere parameters: Knob 1 (CC#74) – Global Controls Cutoff Knob 2 (CC#71) – Global Controls Resonance Knob 3 (CC#79) –…

Setting Up the SQ64

Controllers » Korg » Setting Up the SQ64

When using the Korg SQ64 to control Omnisphere, the knobs on the SQ64 are assigned to the following Omnisphere parameters: Knob 1 (CC#43) – Global Controls Cutoff Knob 2 (CC#39) – Global Controls Ambience Amount Knob 3 (CC#16) – Global…

Setting Up the SP6

Controllers » Kurzweil » Setting Up the SP6

When using the Kurzweil SP6 to control Omnisphere, the knobs on the SP6 will be assigned to the following Omnisphere parameters: Bank 2: Knob 1 (CC#12) – Global Controls Cutoff Knob 2 (CC#13) – Global Controls Resonance Knob 3 (CC#22) – Global…

Setting Up the TRITON

Controllers » Korg » Setting Up the TRITON

When using the Korg Triton to control Omnisphere, the following knobs on the Triton are assigned to the following Omnisphere parameters: Bank A: Knob 1 (CC#74) – Global Controls Cutoff Knob 2 (CC#71) – Global Controls Resonance Knob 3 (CC#79)…

Setting Up the SP3X

Controllers » Kurzweil » Setting Up the SP3X

When using the Kurzweil SP3X to control Omnisphere, the knobs on the SP3X will be assigned to the following Omnisphere parameters: Knob 1 (CC#06) – Global Controls Cutoff Knob 2 (CC#13) – Global Controls Ambience Amount Knob 3 (CC#22) –…

Setting Up the TR

Controllers » Korg » Setting Up the TR

When using the Korg TR to control Omnisphere, the following knobs on the TR are assigned to the following Omnisphere parameters: Bank A: Knob 1 (CC#74) – Global Controls Cutoff Knob 2 (CC#71) – Global Controls Resonance Knob 3 (CC#79) –…

Setting Up the PC88

Controllers » Kurzweil » Setting Up the PC88

When using the Kurzweil PC88 to control Omnisphere, the knobs on the PC88 will be assigned to the following Omnisphere parameters: Knob 1 (CC#91) – Global Controls Cutoff Knob 2 (CC#93) – Global Controls Ambience Amount Knob 3 (CC#04) –…

Setting Up the SP3

Controllers » Kurzweil » Setting Up the SP3

When using the Kurzweil SP3 to control Omnisphere, the knobs on the SP3 will be assigned to the following Omnisphere parameters: Knob 1 (CC#06) – Global Controls Cutoff Knob 2 (CC#13) – Global Controls Ambience Amount Knob 3 (CC#22) – Global…

Setting Up the SP2

Controllers » Kurzweil » Setting Up the SP2

When using the Kurzweil SP2 to control Omnisphere, the knobs on the SP2 will be assigned to the following Omnisphere parameters: Knob 1 (CC#06) – Global Controls Cutoff Knob 2 (CC#13) – Global Controls Ambience Amount Knob 3 (CC#23) – Global…

Setting Up the UMA25S

Controllers » Behringer » Setting Up the UMA25S

When using the Behringer UMA25S to control Omnisphere, the knobs on the UMA25S are assigned to the following Omnisphere parameters: Knob 1 (CC#74) – Global Controls Cutoff Knob 2 (CC#71) – Global Controls Resoance Knob 3 (CC#73) – Global…

Setting Up the PC3X

Controllers » Kurzweil » Setting Up the PC3X

When using the Kurzweil PC3X to control Omnisphere, the sliders on the PC3X will be assigned to the following Omnisphere parameters: Slider 1 (CC#13) – Global Controls Cutoff Slider 2 (CC#22) – Global Controls Resonance Slider 3 (CC#23) –…