Search
Related topics are listed below.
Using SysEx on Windows
Using SysEx on Windows
The following models have controls that send System Exclusive (SysEx) messages: Access Virus C Access Virus TI Roland D50 + PG1000 Roland GAIA Roland JD-XA Roland JD-Xi Roland JP-8000 Roland JP-8080 Roland JUNO-106 Roland Jupiter-X Roland…
Moog Subsequent 25
Synthesizers » Moog » Moog Subsequent 25
The Moog Subsequent 25 is a simple and compact 2-note paraphonic analog synth that combines the high-quality Moog sound with the versatility of a modern instrument. It has a great Multidrive circuit, and you can control the mix of the four Layers, and there’s…
Setting Up the VBoard 25
Controllers » MIDIPlus » Setting Up the VBoard 25
When using the MIDIPlus VBoard 25 to control Omnisphere, the knobs on the VBoard 25 are assigned to the following Omnisphere parameters: Knob 1 (CC#93) – Global Controls Cutoff Knob 2 (CC#91) – Global Controls Ambience Amount Knob 3 (CC#71)…
Setting Up the STARRYKEY 25
Controllers » Donner » Setting Up the STARRYKEY 25
When using the Donner STARRYKEY 25 to control Omnisphere, the knobs on the STARRYKEY 25 are assigned to the following Omnisphere parameters: Knob 1 (CC#20) – Global Controls Cutoff Knob 2 (CC#21) – Global Controls Ambience Amount Knob 3 (CC#22)…
Setting up the Subsequent 25
Synthesizers » Moog » Moog Subsequent 25 » Setting up the Subsequent 25
Setup To control Omnisphere using the Subsequent 25, you’ll need to do the following: Using a USB cable, connect the Subsequent 25, to your computer. Enable the Subsequent 25, as a MIDI input device to Omnisphere in the host software you’re using (DAW,…
Setting up the Masterkey 25
Controllers » Acorn Instruments » Setting up the Masterkey 25
When using the Acorn Instruments Masterkey 25 to control Omnisphere, the knobs on the Masterkey 25 are assigned to the following Omnisphere parameters: Knob 1 (CC#74) – Global Controls Cutoff Knob 2 (CC#71) – Global Controls Ambience Amount Knob 3…
Setting Up the MidAir 25
Controllers » M-Audio » Setting Up the MidAir 25
When using the M-Audio MidAir 25 to control Omnisphere, the knobs on the MidAir 25 are assigned to the following Omnisphere parameters: Knob 1 (CC#91) – Global Controls Cutoff Knob 2 (CC#93) – Global Controls Resonance Knob 3 (CC#05) – Global…
Setting Up the KeyLab 25
Controllers » Arturia » Setting Up the KeyLab 25
When using the Arturia KeyLab 25 to control Omnisphere, the knobs and sliders on the KeyLab 25 are assigned to the following Omnisphere parameters: Knob 01 (CC#74) – Global Controls Cutoff Knob 02 (CC#71) – Global Controls Resonance Knob 03 (CC#76)…
Setting Up the Axiom 25
Controllers » M-Audio » Setting Up the Axiom 25
When using the M-Audio Axiom 25 to control Omnisphere, the knobs on the Axiom 25 are assigned to the following Omnisphere parameters: Knob 1 (CC#71) – Global Controls Cutoff Knob 2 (CC#74) – Global Controls Resonance Knob 3 (CC#84) – Global…
Setting Up the taktile 25
Controllers » Korg » Setting Up the taktile 25
When using the Korg Taktile 25 to control Omnisphere, the following knobs on the Taktile 25 are assigned to the following Omnisphere parameters: Knob 1 (CC#24) – Global Controls Cutoff Knob 2 (CC#25) – Global Controls Resonance Knob 3 (CC#26)…
Setting Up the Launchkey 25 mk4
Controllers » Novation » Setting Up the Launchkey 25 mk4
When using the Novation Launchkey 25 mk4 to control Omnisphere, the knobs and drum pads on the Launchkey 25 mk4 are assigned to the following Omnisphere parameters: Knob 1 (CC#21) – Global Controls Cutoff Knob 2 (CC#22) – Global Controls…
Setting Up the Launchkey 25 mk2
Controllers » Novation » Setting Up the Launchkey 25 mk2
When using the Novation Launchkey 25 mk2 to control Omnisphere, the knobs and buttons on the Launchkey 25 mk2 are assigned to the following Omnisphere parameters: Knob 1 (CC#21) – Global Controls Cutoff Knob 2 (CC#22) – Global Controls…
Setting Up the Launchkey 25 mk3
Controllers » Novation » Setting Up the Launchkey 25 mk3
When using the Novation Launchkey 25 mk3 to control Omnisphere, the knobs and drum pads on the Launchkey 25 mk3 are assigned to the following Omnisphere parameters: Knob 1 (CC#21) – Global Controls Cutoff Knob 2 (CC#22) – Global Controls…
Setting Up the Launchkey 25 mk1
Controllers » Novation » Setting Up the Launchkey 25 mk1
When using the Novation Launchkey 25 mk1 to control Omnisphere, the knobs and buttons on the Launchkey 25 mk1 are assigned to the following Omnisphere parameters: Knob 1 (CC#21) – Global Controls Cutoff Knob 2 (CC#22) – Global Controls…
Setting Up the Oxygen Pro 25
Controllers » M-Audio » Setting Up the Oxygen Pro 25
When using the M-Audio Oxygen Pro 25 to control Omnisphere, the knobs and buttons on the Oxygen Pro 25 are assigned to the following Omnisphere parameters: Knob 1 (cc44) – Global Controls Cutoff Knob 2 (cc45) – Global Controls Resonance Knob 3…
Setting Up the Oxygen 25 mk5
Controllers » M-Audio » Setting Up the Oxygen 25 mk5
When using the M-Audio Oxygen 25 mk5 to control Omnisphere, the knobs on the Oxygen 25 mk5 are assigned to the following Omnisphere parameters: Knob 1 (cc44) – Global Controls Cutoff Knob 2 (cc45) – Global Controls Resonance Knob 3 (cc46) –…
Setting Up the Axiom Pro 25
Controllers » M-Audio » Setting Up the Axiom Pro 25
When using the M-Audio Axiom Pro 25 to control Omnisphere, the knobs on the Axiom Pro 25 are assigned to the following Omnisphere parameters: Knob 1 (CC#10) – Global Controls Cutoff Knob 2 (CC#02) – Global Controls Resonance Knob 3 (CC#12) –…
Setting Up the TRITON taktile 25
Controllers » Korg » Setting Up the TRITON taktile 25
When using the Korg TRITON taktile 25 to control Omnisphere, the following knobs on the TRITON taktile 25 are assigned to the following Omnisphere parameters: Knob 1 (CC#24) – Global Controls Cutoff Knob 2 (CC#25) – Global Controls Resonance Knob 3…
Setting Up the DMK-25 Pro
Controllers » Donner » Setting Up the DMK-25 Pro
When using the Donner DMK-25 Pro to control Omnisphere, the knobs on the DMK-25 Pro are assigned to the following Omnisphere parameters: Bank A: Knob 1 (CC#30) – Global Controls Cutoff Knob 2 (CC#31) – Global Controls Ambience Amount Knob 3 (CC#32)…
Setting Up the iRig Keys IO 25
Controllers » IK Multimedia » Setting Up the iRig Keys IO 25
When using the IK Multimedia iRig Keys IO 25 to control Omnisphere, the knobs on the iRig Keys IO 25 are assigned to the following Omnisphere parameters: First Bank: Knob 1 (CC#12) – Global Controls Cutoff Knob 2 (CC#13) – Global Controls…
Setting Up the APC Key 25 mk2
Controllers » Akai » Setting Up the APC Key 25 mk2
When using the Akai APC Key 25 mk2 to control Omnisphere, the knobs on the APC Key 25 mk2 are assigned to the following Omnisphere parameters: Knob 1 (CC#30) – Global Controls Cutoff Knob 2 (CC#31) – Global Controls Resonance Knob 3 (CC#32)…
Setting Up the iRig Keys 2 25-Key
Controllers » IK Multimedia » Setting Up the iRig Keys 2 25-Key
When using the IK Multimedia iRig Keys 2 to control Omnisphere, the knobs on the iRig Keys 2 are assigned to the following Omnisphere parameters: First Bank: Knob 1 (CC#12) – Global Controls Cutoff Knob 2 (CC#13) – Global Controls Resonance Knob 3…
Setting up the Virus C
Synthesizers » Access » Access Virus C » Setting up the Virus C
Setup To control Omnisphere using the Access Virus C, you’ll need to do the following: Connect the Virus C to your MIDI interface. Set up the Virus C to send System Exclusive messages. Make certain your MIDI interface is configured as the input in the host…
Setting up the D-50 + PG-1000
Synthesizers » Roland » Roland D-50 + PG-1000 » Setting up the D-50 + PG-1000
Setup To control Omnisphere using the the PG-1000, you’ll need to do the following: Connect the MIDI out of the PG-1000 to your MIDI interface. Make certain your MIDI interface is configured as the input in the host software you’re using (DAW, Standalone,…
Setting up the GAIA SH-01
Synthesizers » Roland » Roland GAIA SH-01 » Setting up the GAIA SH-01
Setup To control Omnisphere using the Roland GAIA SH-01, you’ll need to do the following: Connect the GAIA SH-01 to your computer via USB. Download and install the GAIA SH-01’s latest firmware update. Download and install the GAIA SH-01’s USB…
Setting up the Virus TI
Synthesizers » Access » Access Virus TI » Setting up the Virus TI
Setup To control Omnisphere using the Access Virus TI, you’ll need to do the following: Download and install the Virus TI USB driver. Connect the Virus TI to your computer via USB or via the MIDI DIN connector. Set up the Virus TI to send System Exclusive…
Setting up the Virus Indigo 2
Synthesizers » Access » Access Virus Indigo 2 » Setting up the Virus Indigo 2
Setup To control Omnisphere using the Access Virus Indigo 2, you’ll need to do the following: Connect the Virus Indigo 2 to your MIDI interface. Set up the Virus Indigo 2 to send System Exclusive messages. Make certain your MIDI interface is configured as…
Setting up the SH-201
Synthesizers » Roland » Roland SH-201 » Setting up the SH-201
Setup To control Omnisphere using the Roland SH-201, you’ll need to do the following: Connect the Roland SH-201 to your MIDI interface. Make certain your MIDI interface is configured as the input in the host software you’re using (DAW, Standalone,…
Setting up the JD-XA
Synthesizers » Roland » Roland JD-XA » Setting up the JD-XA
Setup To control Omnisphere using the Roland JD-XA, you’ll need to do the following: Connect the JD-XA to your computer via USB. Download and install the latest JD-XA system firmware. Download and install the JD-XA USB driver. Configure the JD-XA to…
Setting up the Super Jupiter
Synthesizers » Roland » Roland Super Jupiter » Setting up the Super Jupiter
Setup To control Omnisphere using the Roland MKS-80 and the MPG-80, you’ll need to do the following: Connect the MKS-80 to your MIDI interface. Set up the MKS-80 to receive/transmit System Exclusive messages. Activate the Roland MKS-80 Hardware Profile in…
Setting up the JUNO-106
Synthesizers » Roland » Roland JUNO-106 » Setting up the JUNO-106
Setup To control Omnisphere using the the Roland JUNO-106, you’ll need to do the following: Connect the JUNO-106 to your computer’s MIDI interface. Set the JUNO-106’s MIDI Function Selector Switch to position “III.” Activate the…
Setting up the JP-8080
Synthesizers » Roland » Roland JP-8080 » Setting up the JP-8080
Setup To control Omnisphere using the the Roland JP-8080, you’ll need to do the following: Connect the JP-8080 to your MIDI interface. Set up the JP-8080’s front panel controls to transmit MIDI. Activate the Roland JP-8080 Hardware Profile in…
Setting up the JP-8000
Synthesizers » Roland » Roland JP-8000 » Setting up the JP-8000
Setup To control Omnisphere using the the Roland JP-8000, you’ll need to do the following: Connect the JP-8000 to your MIDI interface. Set up the JP-8000’s front panel controls to transmit MIDI. Activate the Roland JP-8000 Hardware Profile in…
Setting up the Roland JD-Xi
Synthesizers » Roland » Roland JD-Xi » Setting up the Roland JD-Xi
Setup To control Omnisphere using the Roland JD-Xi you’ll need to do the following: Connect the JD-Xi to your computer via USB. Verify that your JD-Xi system program is up to date with v1.51 (or higher). Download and install the Roland JD-Xi USB…
Setting up the Roland Jupiter-X
Synthesizers » Roland » Roland Jupiter-X » Setting up the Roland Jupiter-X
Setup To control Omnisphere using the Roland Jupiter-X you’ll need to do the following: Connect the Jupiter-X to your computer via USB. Download and install the Jupiter-X USB driver. Set up the Jupiter-X panel controls to transmit MIDI. In the Jupiter-X,…
Setting up the Roland Jupiter-Xm
Synthesizers » Roland » Roland Jupiter-Xm » Setting up the Roland Jupiter-Xm
Setup To control Omnisphere using the Roland Jupiter-Xm you’ll need to do the following: Connect the Jupiter-Xm to your computer via USB. Download and install the Jupiter-Xm USB driver. Set up the Jupiter-Xm panel controls to transmit MIDI. In the…
Setting Up the taktile 49
Controllers » Korg » Setting Up the taktile 49
When using the Korg Taktile 49 to control Omnisphere, the following knobs and sliders on the Taktile 49 are assigned to the following Omnisphere parameters: Knob 1 (CC#16) – Global Controls Cutoff Knob 2 (CC#17) – Global Controls Resonance Knob 3…
Setting Up the Keystage 61
Controllers » Korg » Setting Up the Keystage 61
KORG KEYSTAGE 61 When using the Korg Keystage 61 to control Omnisphere, the following knobs on the Keystage 61 are assigned to the following Omnisphere parameters: Knob 1 (CC#24) – Global Controls Cutoff Knob 2 (CC#25) – Global Controls…
Setting Up the Keystage 49
Controllers » Korg » Setting Up the Keystage 49
When using the Korg Keystage 49 to control Omnisphere, the following knobs on the Keystage 49 are assigned to the following Omnisphere parameters: Knob 1 (CC#24) – Global Controls Cutoff Knob 2 (CC#25) – Global Controls Resonance Knob 3 (CC#26)…
Setting Up the nanoKEY Studio
Controllers » Korg » Setting Up the nanoKEY Studio
When using the Korg nanoKEY Studio to control Omnisphere, the following knobs on the nanoKEY Studio are assigned to the following Omnisphere parameters: Knob 1 (CC#20) – Global Controls Cutoff Knob 2 (CC#21) – Global Controls Resonance Knob 3…
Setting Up the TRITON taktile 49
Controllers » Korg » Setting Up the TRITON taktile 49
When using the Korg TRITON taktile 49 to control Omnisphere, the following knobs and sliders on the TRITON taktile 49 are assigned to the following Omnisphere parameters: Knob 1 (CC#16) – Global Controls Cutoff Knob 2 (CC#17) – Global Controls…
Setting Up the VI25
Controllers » Alesis » Setting Up the VI25
When using the Alesis VI25 to control Omnisphere, the Knobs on the VI25 are assigned to the following Omnisphere parameters: Knob 1 (C#C20) – Global Controls Cutoff Knob 2 (CC#21) – Global Controls Resonance Knob 3 (CC#22) – Global Controls…
Setting Up the VI49
Controllers » Alesis » Setting Up the VI49
When using the Alesis VI49 to control Omnisphere, the Knobs on the VI49 are assigned to the following Omnisphere parameters: Knob 01 (CC#20) – Global Controls Cutoff Knob 02 (CC#21) – Global Controls Resonance Knob 03 (CC#22) – Global…
Setting up the Circuit Mono Station
Synthesizers » Novation » Novation Circuit Mono Station » Setting up the Circuit Mono Station
Setup To control Omnisphere using the Novation Circuit Mono Station, you’ll need to do the following: Using a USB cable, connect the Circuit Mono Station to your computer. If you’re using a Windows-based system, download the Novation USB 2.11…
Setting Up the MAX25
Controllers » Akai » Setting Up the MAX25
When using the Akai MAX25 to control Omnisphere, the Touch Faders on the MAX25 are assigned to the following Omnisphere parameters: Bank 1-4: Touch Fader 1 (CC#20) – Global Controls Cutoff Touch Fader 2 (CC#21) – Global Controls Ambience…
Setting Up the VI61
Controllers » Alesis » Setting Up the VI61
When using the Alesis VI61 to control Omnisphere, the Knobs on the VI61 are assigned to the following Omnisphere parameters: Knob 01 (CC#20) – Global Controls Cutoff Knob 02 (CC#21) – Global Controls Resoance Knob 03 (CC#22) – Global…
Roland GAIA SH-01
Synthesizers » Roland » Roland GAIA SH-01
The Roland GAIA SH-01 is a great controller for Omnisphere. The most interesting aspect about it is that you have independent control over three Layers using an intuitive panel. You can access multiple Filter types, Wavetables and it has a great FX section.…
Roland JUNO-106
Synthesizers » Roland » Roland JUNO-106
The Roland Juno-106 is a classic analog polysynth and remains popular due to its great sound and easy programmability. The panel provides basic control over Omnisphere, but enough to create a wide array of classic synth sounds. The fact the keyboard has no velocity…
Roland Super Jupiter
Synthesizers » Roland » Roland Super Jupiter
The Roland Super Jupiter is a classic analog synth that comes in a 2-space rack module. Most people who own it also have the MPG-80 programmer, which gives you all the controls you need to program sounds on the Super Jupiter. Although it doesn’t have tons of…
Roland JP-8080
Synthesizers » Roland » Roland JP-8080
The JP-8080 is a virtual analog synth Roland made in the mid-‘90s. It has become a modern classic, mostly because it introduced the Supersaw sound, which pretty much defined Trance music. The panel is really good, you have a lot of hands-on control: 2…
Setting up the Reface CS
Synthesizers » Yamaha Reface CS » Setting up the Reface CS
Setup To control Omnisphere using the Yamaha Reface CS, you’ll need to do the following: Connect the Reface CS to your computer via USB. If you’re using a Windows-based system, download the Yamaha USB Driver. Enable MIDI control on the Reface…
Roland D-50 + PG-1000
Synthesizers » Roland » Roland D-50 + PG-1000
The Roland D-50 was a true phenomenon when it came out in the 1980s. It was on the cutting edge and its sound was ubiquitous. It could be heard on every record, every TV show, and every film. Although compartmentalized a bit, today, this classic synth retains its…
Roland JD-XA
Synthesizers » Roland » Roland JD-XA
The Roland JD-XA is an interesting controller for Omnisphere. One of its most powerful features is that you can switch and layer the Parts you are controlling on-the-fly. In Parts 1–4, the Layers in Omnisphere share the same Envelopes, Filters, and LFOs. Parts…
Access Virus C
Synthesizers » Access » Access Virus C
The Access Virus C is a classic synth from the early 2000s. Compared to its predecessor, the Virus B, it has more polyphony and expanded modulation capabilities, among other things. From its panel, you have access to many of Omnisphere’s Wavetables,…
Roland JD-Xi
Synthesizers » Roland » Roland JD-Xi
The Roland JD-Xi is a good option if you want some basic control over Omnisphere in a portable format. You have access to multiple Filter types, an LFO, and a pretty capable FX section. The main downside is that the Envelope is adjusted from a single knob, so you…
Roland SH-201
Synthesizers » Roland » Roland SH-201
The Roland SH-201 is a virtual analog synth from the mid 2000’s. The panel is well laid out, making it easy to program sounds, giving you control over 2 Oscillators, multiple Filter types, 3 LFOs, and FX. It doesn’t have a Mod Wheel, but if you’re…
Roland JP-8000
Synthesizers » Roland » Roland JP-8000
The Roland JP-8000 is a virtual analog synth made in the mid-‘90s. It has become a modern classic, mostly because it introduced the Supersaw sound, which pretty much defined Trance music. The panel is really good, you have a lot of hands-on control — 2…
Roland Jupiter-X
Synthesizers » Roland » Roland Jupiter-X
The Roland Jupiter-X is a powerful synth with a flexible engine that can reproduce sounds from different Roland eras, from the Jupiter-8 to the XV-5080, including modern RD pianos. The build quality is very good, and we like that it has wheels in addition to…
Setting Up the Komplete Kontrol S25 mk1
Controllers » Native Instruments » Setting Up the Komplete Kontrol S25 mk1
When using the NI Komplete Kontrol S25 mk1 to control Omnisphere, the knobs on the Komplete Kontrol S25 mk1 are assigned to the following Omnisphere parameters: Knob 1 (CC#14) – Global Controls Cutoff Knob 2 (CC#15) – Global Controls…
Setting Up the Komplete Kontrol S88 mk2
Controllers » Native Instruments » Setting Up the Komplete Kontrol S88 mk2
When using the NI Komplete Kontrol S88 mk2 to control Omnisphere, the knobs on the Komplete Kontrol S88 mk2 are assigned to the following Omnisphere parameters: Knob 1 (CC#14) – Global Controls Cutoff Knob 2 (CC#15) – Global Controls…
Setting Up the Komplete Kontrol S61 mk1
Controllers » Native Instruments » Setting Up the Komplete Kontrol S61 mk1
When using the NI Komplete Kontrol S61 mk1 to control Omnisphere, the knobs on the Komplete Kontrol S61 mk1 are assigned to the following Omnisphere parameters: Knob 1 (CC#14) – Global Controls Cutoff Knob 2 (CC#15) – Global Controls…
Setting Up the Komplete Kontrol S61 mk2
Controllers » Native Instruments » Setting Up the Komplete Kontrol S61 mk2
When using the NI Komplete Kontrol S61 mk2 to control Omnisphere, the knobs on the Komplete Kontrol S61 mk2 are assigned to the following Omnisphere parameters: Knob 1 (CC#14) – Global Controls Cutoff Knob 2 (CC#15) – Global Controls…
Setting Up the Komplete Kontrol S88 mk1
Controllers » Native Instruments » Setting Up the Komplete Kontrol S88 mk1
When using the NI Komplete Kontrol S88 mk1 to control Omnisphere, the knobs on the Komplete Kontrol S88 mk1 are assigned to the following Omnisphere parameters: Knob 1 (CC#14) – Global Controls Cutoff Knob 2 (CC#15) – Global Controls…
Setting Up the Komplete Kontrol S49 mk2
Controllers » Native Instruments » Setting Up the Komplete Kontrol S49 mk2
When using the NI Komplete Kontrol S49 mk2 to control Omnisphere, the knobs on the Komplete Kontrol S49 mk2 are assigned to the following Omnisphere parameters: Knob 1 (CC#14) – Global Controls Cutoff Knob 2 (CC#15) – Global Controls Resonance Knob…
Setting Up the Komplete Kontrol S49 mk1
Controllers » Native Instruments » Setting Up the Komplete Kontrol S49 mk1
When using the NI Komplete Kontrol S49 mk1 to control Omnisphere, the knobs on the Komplete Kontrol S49 mk1 are assigned to the following Omnisphere parameters: Knob 1 (CC#14) – Global Controls Cutoff Knob 2 (CC#15) – Global Controls…
Access Virus Indigo 2
Synthesizers » Access » Access Virus Indigo 2
The Access Virus Indigo 2 is a Virus C with a 37-note keyboard. From its panel, you have access to many of Omnisphere’s Wavetables, Dual-filter architecture, LFOs, and FX. The layout allows you to get a wide variety of sounds, so producers of all genres will…
Setting Up the Vortex Wireless 2
Controllers » Alesis » Setting Up the Vortex Wireless 2
When using the Alesis Vortex Wireless 2 to control Omnisphere, the Faders on the Vortex Wireless 2 are assigned to the following Omnisphere parameters: Fader 1 (CC#36) – Global Controls Cutoff Fader 2 (CC#37) – Global Controls Resonance Fader 3…
Roland Jupiter-Xm
Synthesizers » Roland » Roland Jupiter-Xm
The Roland Jupiter-Xm is a smaller version of the Jupiter-X, and has a flexible engine that can reproduce sounds from different Roland eras, from the Jupiter-8 to the XV-5080, including modern RD pianos. Although more limited, the panel is more intuitive to use…
Setting Up the Launchkey Mini mk3
Controllers » Novation » Setting Up the Launchkey Mini mk3
When using the Novation Launchkey Mini mk3 to control Omnisphere, the knobs on the Launchkey Mini mk3 are assigned to the following Omnisphere parameters: Knob 1 (CC#21) – Global Controls Cutoff Knob 2 (CC#22) – Global Controls Resonance Knob 3…
Setting Up the FL Key Mini
Controllers » Novation » Setting Up the FL Key Mini
When using the Novation FL Key Mini to control Omnisphere, the knobs on the FL Key Mini are assigned to the following Omnisphere parameters: Knob 1 (CC#21) – Global Controls Cutoff Knob 2 (CC#22) – Global Controls Resonance Knob 3 (CC#23) –…
Setting Up the FL Key 37
Controllers » Novation » Setting Up the FL Key 37
When using the Novation FL Key 37 to control Omnisphere, the knobs on the FL Key 37 are assigned to the following Omnisphere parameters: Knob 1 (CC#21) – Global Controls Cutoff Knob 2 (CC#22) – Global Controls Resonance Knob 3 (CC#23) – Global…
Setting up the Peak
Synthesizers » Novation » Novation Peak » Setting up the Peak
Setup To control Omnisphere using the Novation Peak, you’ll need to do the following: Using a USB cable, connect the Novation Peak to your computer. If you’re using a Windows-based system, download the Novation USB Driver. Set up the front panel…
Setting up the Summit
Synthesizers » Novation » Novation Summit » Setting up the Summit
Setup To control Omnisphere using the Novation Summit, you’ll need to do the following: Using a USB cable, connect the Novation Summit to your computer. If you’re using a Windows-based system, download the Novation USB Driver. Set up the front panel…
Setting up the MPK Mini mk4
Controllers » Akai » Setting up the MPK Mini mk4
When using the Akai MPK Mini mk4 to control Omnisphere, the knobs and drum pads on the MPK Mini mk4 are assigned to the following Omnisphere parameters: Knob 1 (CC#24) – Global Controls Cutoff Knob 2 (CC#25) – Global Controls Resonance Knob 3…
Setting Up the SP6
Controllers » Kurzweil » Setting Up the SP6
When using the Kurzweil SP6 to control Omnisphere, the knobs on the SP6 will be assigned to the following Omnisphere parameters: Bank 2: Knob 1 (CC#12) – Global Controls Cutoff Knob 2 (CC#13) – Global Controls Resonance Knob 3 (CC#22) – Global…
Setting Up the PC3X
Controllers » Kurzweil » Setting Up the PC3X
When using the Kurzweil PC3X to control Omnisphere, the sliders on the PC3X will be assigned to the following Omnisphere parameters: Slider 1 (CC#13) – Global Controls Cutoff Slider 2 (CC#22) – Global Controls Resonance Slider 3 (CC#23) –…
Setting Up the PC3
Controllers » Kurzweil » Setting Up the PC3
When using the Kurzweil PC3 to control Omnisphere, the sliders on the PC3 will be assigned to the following Omnisphere parameters: Slider 1 (CC#13) – Global Controls Cutoff Slider 2 (CC#22) – Global Controls Resonance Slider 3 (CC#23) – Global…
Setting Up the PC3K
Controllers » Kurzweil » Setting Up the PC3K
When using the Kurzweil PC3K to control Omnisphere, the sliders on the PC3K will be assigned to the following Omnisphere parameters: Slider 1 (CC#13) – Global Controls Cutoff Slider 2 (CC#22) – Global Controls Resonance Slider 3 (CC#23) –…
Setting Up the PC3A
Controllers » Kurzweil » Setting Up the PC3A
When using the Kurzweil PC3A to control Omnisphere, the sliders on the PC3A will be assigned to the following Omnisphere parameters: Slider 1 (CC#13) – Global Controls Cutoff Slider 2 (CC#22) – Global Controls Resonance Slider 3 (CC#23) –…
Setting Up the Oxygen Pro Mini
Controllers » M-Audio » Setting Up the Oxygen Pro Mini
When using the M-Audio Oxygen Pro Mini to control Omnisphere, the knobs on the Oxygen Pro Mini are assigned to the following Omnisphere parameters: Bank 1: Knob 1 (CC#120) – Global Controls Cutoff Knob 2 (CC#121) – Global Controls Resonance Knob 3…
Setting Up the Launchkey 37 mk4
Controllers » Novation » Setting Up the Launchkey 37 mk4
When using the Novation Launchkey 37 mk4 to control Omnisphere, the knobs and drum pads on the Launchkey 37 mk4 are assigned to the following Omnisphere parameters: Knob 1 (CC#21) – Global Controls Cutoff Knob 2 (CC#22) – Global Controls…
Setting Up the KARMA
Controllers » Korg » Setting Up the KARMA
When using the Korg KARMA to control Omnisphere, the following knobs on the KARMA are assigned to the following Omnisphere parameters: KARMA Realtime Controls: Knob 1 (CC#22) – Global Controls Cutoff Knob 2 CC#23) – Global Controls Resonance Knob…
Setting Up the STARRYKEY 37
Controllers » Donner » Setting Up the STARRYKEY 37
When using the Donner STARRYKEY 37 to control Omnisphere, the knobs on the STARRYKEY 37 are assigned to the following Omnisphere parameters: Knob 1 (CC#24) – Global Controls Cutoff Knob 2 (CC#25) – Global Controls Resonance Knob 3 (CC#26) –…
Access Virus TI
Synthesizers » Access » Access Virus TI
The Access Virus TI is the most powerful of all the Virus models. It has many improvements over its predecessors, including new oscillator features, effects, and DAW integration, to name just a few. When it comes to controlling Omnisphere, from its panel you can…
Setting Up the MPK Mini mk1
Controllers » Akai » Setting Up the MPK Mini mk1
When using the Akai MPK Mini mk1 to control Omnisphere, the knobs and drum pads on the MPK Mini mk1 are assigned to the following Omnisphere parameters: Knob 1 (CC#17) – Global Controls Cutoff Knob 2 (CC#18) – Global Controls Resonance Knob 3…
Setting Up the MPD232
Controllers » Akai » Setting Up the MPD232
When using the Akai MPD232 to control Omnisphere, the knobs and sliders on the MPD232 are assigned to the following Omnisphere parameters: Knob 1 (CC#03) – Global Controls Cutoff Knob 2 (CC#09) – Global Controls Resonance Knob 3 (CC#14) –…
Setting Up the 49SL mkIII
Controllers » Novation » Setting Up the 49SL mkIII
When using the Novation 49SL mk3 to control Omnisphere, the knobs, faders, and buttons on the 49SL mk3 are assigned to the following Omnisphere parameters: Knob 1 (CC#21) – Global Controls Cutoff Knob 2 (CC#22) – Global Controls Resonance Knob 3…
Setting Up the Launchkey Mini mk2
Controllers » Novation » Setting Up the Launchkey Mini mk2
When using the Novation Launchkey Mini mk2 to control Omnisphere, the knobs and buttons on the Launchkey Mini mk2 are assigned to the following Omnisphere parameters: Knob 1 (CC#21) – Global Controls Cutoff Knob 2 (CC#22) – Global Controls…
Setting Up the Launchkey Mini mk1
Controllers » Novation » Setting Up the Launchkey Mini mk1
When using the Novation Launchkey Mini mk1 to control Omnisphere, the knobs and buttons on the Launchkey Mini mk1 are assigned to the following Omnisphere parameters: Knob 1 (CC#21) – Global Controls Cutoff Knob 2 (CC#22) – Global Controls…
Setting Up The Player
Controllers » Arturia » Setting Up The Player
When using the Arturia Player to control Omnisphere, the knobs and sliders on the Player are assigned to the following Omnisphere parameters: First Bank: Knob 1 (CC#74) – Global Controls Cutoff Knob 2 (CC#71) – Global Controls Resonance Knob 3…
Setting Up the iRig Keys IO 49
Controllers » IK Multimedia » Setting Up the iRig Keys IO 49
When using the IK Multimedia iRig Keys IO 49 to control Omnisphere, the knobs on the iRig Keys IO 49 are assigned to the following Omnisphere parameters: First Bank: Knob 1 (CC#12) – Global Controls Cutoff Knob 2 (CC#13) – Global Controls…
Setting Up the SQ64
Controllers » Korg » Setting Up the SQ64
When using the Korg SQ64 to control Omnisphere, the knobs on the SQ64 are assigned to the following Omnisphere parameters: Knob 1 (CC#43) – Global Controls Cutoff Knob 2 (CC#39) – Global Controls Ambience Amount Knob 3 (CC#16) – Global…
Setting Up the 61SL mkIII
Controllers » Novation » Setting Up the 61SL mkIII
When using the Novation 61SL mk3 to control Omnisphere, the knobs, faders, and buttons on the 61SL mk3 are assigned to the following Omnisphere parameters: Knob 1 (CC#21) – Global Controls Cutoff Knob 2 (CC#22) – Global Controls Resonance Knob 3…
Setting Up the Launchkey 37 mk3
Controllers » Novation » Setting Up the Launchkey 37 mk3
When using the Novation Launchkey 37 mk3 to control Omnisphere, the knobs and drum pads on the Launchkey 37 mk3 are assigned to the following Omnisphere parameters: Knob 1 (CC#21) – Global Controls Cutoff Knob 2 (CC#22) – Global Controls…
Setting Up the Launchkey Mini mk4
Controllers » Novation » Setting Up the Launchkey Mini mk4
When using the Novation Launchkey Mini mk4 to control Omnisphere, the knobs and drum pads on the Launchkey Mini mk4 are assigned to the following Omnisphere parameters: Knob 1 (CC#21) – Global Controls Cutoff Knob 2 (CC#22) – Global Controls…
Setting Up the Launchkey Mini 37 mk4
Controllers » Novation » Setting Up the Launchkey Mini 37 mk4
When using the Novation Launchkey Mini 37 mk4 to control Omnisphere, the knobs and drum pads on the Launchkey Mini 37 mk4 are assigned to the following Omnisphere parameters: Knob 1 (CC#21) – Global Controls Cutoff Knob 2 (CC#22) – Global Controls…
Setting Up the FL Key 61
Controllers » Novation » Setting Up the FL Key 61
When using the Novation FL Key 61 to control Omnisphere, the knobs and sliders on the FL Key 61 are assigned to the following Omnisphere parameters: Knob 1 (CC#21) – Global Controls Cutoff Knob 2 (CC#22) – Global Controls Resonance Knob 3 (CC#23)…
Setting Up the FL Key 49
Controllers » Novation » Setting Up the FL Key 49
When using the Novation FL Key 49 to control Omnisphere, the knobs and sliders on the FL Key 49 are assigned to the following Omnisphere parameters: Knob 1 (CC#21) – Global Controls Cutoff Knob 2 (CC#22) – Global Controls Resonance Knob 3 (CC#23)…
Setting Up the Launch Control
Controllers » Novation » Setting Up the Launch Control
When using the Novation Launch Control to control Omnisphere, the knobs and buttons on the Launch Control are assigned to the following Omnisphere parameters: Top Row of Knobs: Knob 1 (CC#21) – Global Controls Cutoff Knob 2 (CC#22) – Global Controls…
Setting Up the M3
Controllers » Korg » Setting Up the M3
When using the Korg M3 to control Omnisphere, the following sliders on the M3 are assigned to the following Omnisphere parameters: Slider 1 (CC#08) – Global Controls Cutoff Slider 2 (CC#71) – Global Controls Resonance Slider 3 CC#74) –…
